Fet Amp

Besides the resistive function, MOSFETs can also perform an amplification function. Let’s consider how we can obtain the amplification function from a MOSFET.

Fet Amplifier Experiment
Fet Amplifier
Fet Amplifier

A Cascade of Three FET Stages: Current Source Biasing ID1 VDD ID2 VDD VBIAS vin M1 M2 ID3 VDD VOUT vout M3 IREF VDD M4 M5 M6 The sizes (W/L ratios) of M4, M5, and M6can be adjusted to get the desired bias currents for the three amplifier stages MA MB ECE 315 –Spring 2007 –Farhan Rana –Cornell University A Cascade of CS and CG: A. Waves - CLA-76 (1176 style) Softube - FET Compressor (1176 style) Accustica Audio - Viridian2 (1176 style) Waves - dbx-160 Apple Logic Pro X - Classic VCA (d.

Figure 1. The transverse characteristic of MOSFET operation. There are three lines depicted that are the focus of the $v_{D S} = v_{G S} - v_{T}$ .

Figure 1 depicts the transverse characteristics for a MOSFET. During the MOSFET operation we can see three working regimes – the triode regime, off-regime and saturation regime. During the off-regime, the MOSFET does not operates.

The triode regime characterises the resistive operation of a MOSFET. The saturation regime characterises the amplification function of the MOSFET. As we know

v_{D S} < v_{G S} - v_{T}

corresponds to the triode regime, the saturation regime is

v_{D S} > v_{G S} - v_{T}

. In the saturation regime the MOSFET works as a current source. The operation of a MOSFET can be represented as the switch current source (SCS) model, which is used only at the saturation operation model. The SCS model of the MOSFET is depicted in Figure 2.

Fet Amplifier Experiment

When the MOSFET is in the saturation regime, it will be characterised with the following parameters:

i_{D S} = \frac{K}{2} {v_{D S}}^{2}

, and the saturation regime works only when

v_{D S} > v_{G S} - v_{T}

, so the

i_{D S} = \frac{K}{2} (v_{G S} - v)^{2}

Modern amplifiers are usually manufactured using the MOSFET’s inside. Let’s consider the simplified scheme of the amplifier, depicted in Figure 3. Let’s find the output voltage

v_{O}

as the function of input voltage

v_{i n}

In accordance to the circuit

v_{O} = V_{S} - R_{L} \frac{K}{2} (v_{i n} - V_{T})^{2}

. The ratio of

\frac{v_{o}}{v_{i n}} = \frac{V_{S} - R_{L} \frac{K}{2} (v_{i n} - V_{T})^{2}}{v_{i n}}

. This relationship is a transfer function of the amplifier, and is depicted in Figure 4. This ratio shows the voltage gain of the amplifier, and it is a non-linear function and depends on the input voltage, that positions the MOSFET in the saturation regime.

Figure 3. Simplified scheme of the MOSFET.

Fet Amplifier

Figure 4.The input vs output voltage ratio for the MOSFET amplifier.

In practical amplifiers, the input and output are tied up to the same ground. In order for every input signal to be amplified, it should match a certain range of voltages, so we can use bias voltages for these purposes.

Let’s consider the input voltage as the sum of the input voltage, plus the biased voltage

v_{i n} = v_{x} + v_{b i a s}

. The output voltage in this case will consist of two constituents

v_{o u t} = v_{y} + v_{b i a s 2}

. As far as

v_{y}

is the amplified voltage of

v_{x}

, the

v_{b i a s 2}

is the amplified voltage of

v_{b i a s 1}

. The bias voltage is important as it affects the operation point, so the operation point for the amplifier is called the amplifier bias point.

Fet Amplifier

A large signal model of the MOSFET amplifier helps to answer the question of the relationship between the output voltage and input voltage, when the input voltage changes significantly, and what is the valid voltage range for a MOSFET amplifier? The valid voltage range for the MOSFET amplifier is the band of input voltages when the MOSFET amplifier works in the saturation regime. The lowest valid input voltage is

V_{T}

, the highest is

\frac{- 1 + \sqrt{1 + 2 V_{s} R_{L} K}}{R_{L} K}